Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Mon Apr 15, 2024 11:12 pm

View unanswered posts | View active topics


Board index » Buy, Sell, Trade » Freelance Services

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.



Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
kobs
 Post subject: Need machining done
PostPosted: Sun Sep 22, 2013 4:45 pm 
Offline

Joined: Wed May 22, 2013 1:00 pm
Posts: 474
i made a barrel shroud for my 2240 and used rubber washers to hold it on the barrel it looks like.... well rubber washers holding the shroud loll so i would like to change that to some kind of a muzzle break, shorter but same look
Image



So i need 2 pieces made
1st piece would fit gas cap side, the other would be the end of the break

One that will fit on the barrel which is 1.1 cm so the piece should be 1.1 inside dimension. The other end should be able to take a 3/4 inch OD pipe (like a reducer) i would like the piece fitting on the barrel to be 3 cm long and the piece on the 3/4 inch pipe 3 cm long as well

the other piece would be 3/4 inch inside dimension so it fits the other end of the break 3cm long as well but the other end closed with a 17/64 inch hole in the middle could be a bit bigger but no smaller .

yes i want them to fit over the pipe not inside lol

Both pieces should have tapping screws to hold it in place, the first piece (reducer) one on each size obviously and the second if it's possible 2, one on top and bottom.

would like it steel if possible if not the strongest metal down the line.
Thickness is left at your discretion i know nothing about metalurgy so i have no idea what is best. i do want it to hold tho lol

PM me if you need more info and the price it would cost to make

thanks :wink:
Top
 Profile  
 
Ace
 Post subject: Re: Need machining done
PostPosted: Sun Sep 22, 2013 5:06 pm 
Offline
User avatar

Joined: Mon Feb 11, 2013 12:46 am
Posts: 5705
PM Rick - AKA rrdstarr I'm sure he can make what you want :wink:

_________________
"A candle loses nothing by lighting another candle"

Image
Top
 Profile  
 
rrdstarr
 Post subject: Re: Need machining done
PostPosted: Sun Sep 22, 2013 6:33 pm 
Offline
User avatar

Joined: Sun Jul 15, 2012 10:49 am
Posts: 6030
Location: Victoria, BC and Clarkston, WA
I need a drawing of what you want. Make the drawing in Inch please!
rdstarr1963@gmail.com

Thanks Ace! :D

_________________
-Rick

Brocock Concept .22
3 Crosman MK 1 pistol .22
Top
 Profile  
 
kobs
 Post subject: Re: Need machining done
PostPosted: Sun Sep 22, 2013 6:41 pm 
Offline

Joined: Wed May 22, 2013 1:00 pm
Posts: 474
Omg drawing.... lol i'll do my best

thanks :D
Top
 Profile  
 
rrdstarr
 Post subject: Re: Need machining done
PostPosted: Sun Sep 22, 2013 6:58 pm 
Offline
User avatar

Joined: Sun Jul 15, 2012 10:49 am
Posts: 6030
Location: Victoria, BC and Clarkston, WA
kobs wrote:
Omg drawing.... lol i'll do my best

thanks :D


Bar napkin sketches are good! But not after 12 Cokes and Bacardi! :drinkers:

_________________
-Rick

Brocock Concept .22
3 Crosman MK 1 pistol .22
Top
 Profile  
 
kobs
 Post subject: Re: Need machining done
PostPosted: Sun Sep 22, 2013 7:39 pm 
Offline

Joined: Wed May 22, 2013 1:00 pm
Posts: 474
sketch sent :)
Top
 Profile  
 
kobs
 Post subject: Re: Need machining done
PostPosted: Wed Oct 02, 2013 11:39 am 
Offline

Joined: Wed May 22, 2013 1:00 pm
Posts: 474
Received my machined pieces today,Rick is "DA MAN" loll. The dimensions are to a T,they fit perfectly and they look even better than i expected :D

Thank you so much :wink:
Top
 Profile  
 
rrdstarr
 Post subject: Re: Need machining done
PostPosted: Wed Oct 02, 2013 4:52 pm 
Offline
User avatar

Joined: Sun Jul 15, 2012 10:49 am
Posts: 6030
Location: Victoria, BC and Clarkston, WA
Anytime! It was a pretty straightforward job.

_________________
-Rick

Brocock Concept .22
3 Crosman MK 1 pistol .22
Top
 Profile  
 
Voltar1
 Post subject: Re: Need machining done
PostPosted: Wed Oct 02, 2013 5:16 pm 
Offline

Joined: Mon Sep 05, 2005 10:55 pm
Posts: 6936
Location: Rocky Mtn Hse Alberta
kobs wrote:
Received my machined pieces today,Rick is "DA MAN" loll. The dimensions are to a T,they fit perfectly and they look even better than i expected :D

Thank you so much :wink:


Pics??

_________________
Image
Walter
Top
 Profile  
 
kobs
 Post subject: Re: Need machining done
PostPosted: Wed Oct 02, 2013 9:46 pm 
Offline

Joined: Wed May 22, 2013 1:00 pm
Posts: 474
sure :)

Image

Image

Much better than my rubber washers... now it's got class :lol:
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Buy, Sell, Trade » Freelance Services

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO