Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Thu Dec 08, 2022 4:06 am

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.






Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: Wed May 25, 2022 6:03 pm 
Offline

Joined: Sat Oct 03, 2020 9:07 pm
Posts: 59
Location: Muskoka,Ontario,Canada
I’ve been looking for an alternative to the uncomfortable chaser stock, so when I saw this at airgun archery(AA) I thought I’d give it a go. I have never dealt with 3D printed upgrades before so I wasn’t sure what I was getting into. First, the parts came extremely well packed from AA. I watched the video for installation instructions as per the link on AA.
As per the video I had to sand the buffer tube to achieve a nice tight fit. The trigger frame required lots of tweaking to get it to fit properly. The rear pin on the trigger was too long to fit so I ground it down.it still wouldn’t fit, so I used a magic marker to identify where the frame was hitting.Then I used a dremel with a small stone to remove just enough material to get it to fit. The fitting of the trigger housing took about a 1/2hour.
The 3D printing is quite good, with just a bit of a rough spot inside the trigger guard. I smoothed that out carefully with the dremel then coloured it with black sharpie(you can’t even notice it now).
Once the fitting mods were done it went together easily. There was a warning about over tightening the grip so be aware.
The grip is kinda cheap but it works, I’m gonna check out Epps this week to upgrade to a magpul grip.
After taking my first shot I couldn’t believe how well it felt, this kit has brought new life to my chaser. While it’s always been a fun shooter it’s now at the next level. I added a foregrip/bypod which I had from a Ruger SR22 I used to have, a red dot, and a laser. This is the ultimate ratter now.

Pros- looks great,functions great,AR grips are upgradable, pieces are sold separately

Cons- kinda pricey at $147.20+shipping for full kit(short pic rail for chaser), expect to modify the AR trigger frame to fit (it’s not difficult to do,just take your time.)

I really like this kit,I would recommend it.
Just a note,none of the modifications you’ll need to make, compromise the integrity of the trigger frame.


Attachments:
F58A6503-B672-4382-8DD9-3F0D7CDDAE86.jpeg
F58A6503-B672-4382-8DD9-3F0D7CDDAE86.jpeg [ 689.19 KiB | Viewed 255 times ]
524CF43A-8E92-4AE5-8D49-C589D615CBD0.jpeg
524CF43A-8E92-4AE5-8D49-C589D615CBD0.jpeg [ 715.34 KiB | Viewed 255 times ]

_________________
“If women don’t find you handsome ,they should at least find you handy” -Red Green
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO