| Canadian Airgun Forum https://www.airgunforum.ca/forums/ |
|
| What Did You Do To Your Airgun Today? https://www.airgunforum.ca/forums/topic74188-435.html |
Page 30 of 32 |
| Author: | CBS shooter [ Tue Jun 04, 2019 4:31 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
I got it an air supply for it and i want to fill it. But I am not sure if the new warrior compressor has to have oil first. It says to oil every 5 fills, but do I add more after 5 or do I have to add first to start. Then every 5 after  has a test card on it wouldn't it have to have had oil to test it   ships with bottle but no oil in it. If it needs oil now it will have to wait tell I get some. where to get silicone oil If anyone can, help me please
|
|
| Author: | Daryl [ Tue Jun 04, 2019 11:47 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
Picked up my Condor .25 and dry fired it. Other than that, nothing. I did load up 50 rounds of 6.5x55 with 85gr. HP's though & annealed and dried another 50 cases for it. |
|
| Author: | shoot [ Fri Jun 14, 2019 6:54 pm ] | ||||
| Post subject: | Re: What Did You Do To Your Airgun Today? | ||||
Guess on what I did it yesterday... Basically took the spring / piston / lever out and put in this.
|
|||||
| Author: | Canadianguy [ Fri Sep 06, 2019 8:09 am ] | ||
| Post subject: | Re: What Did You Do To Your Airgun Today? | ||
I couldn't stand the look of those plastic open sights any longer on the DPMS and picked these up on Amazon.I like the way to they click into place.
|
|||
| Author: | Ronan_357 [ Sun Sep 08, 2019 9:21 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
I had resealed my marauder after having to deburr every hole, it only cost me 3 o rings to figure that out. Also installed a jsa balanced valve, i’m looking forward to trying it out. |
|
| Author: | YepYep [ Thu Sep 12, 2019 2:27 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
Recieved my new orders of the carbon fiber tubes from China and trimmed and put on my 2240 which brings it a new look~   Sent from my S8 via Tapatalk |
|
| Author: | walther [ Sun Sep 15, 2019 12:33 pm ] |
| Post subject: | What Did You Do To Your Airgun Today? |
carbon tube is really cool and fun to work with looks nice on there. I've got several pieces at home , one of which is destined for my CR 600w In a similar fashion. One suggestion , instead of sanding down the end of your tube to match your muzzle brake, I would have reduce the length of the muzzle break so the diameter matches up perfectly with the diameter of the carbon tube then it would look seamless. |
|
| Author: | wesb2007 [ Sun Sep 15, 2019 4:37 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
YepYep wrote: Recieved my new orders of the carbon fiber tubes from China and trimmed and put on my 2240 which brings it a new look~ Very cool!Sent from my S8 via Tapatalk Sent from my EML-L09 using Tapatalk |
|
| Author: | YepYep [ Sun Sep 15, 2019 4:59 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
walther wrote: One suggestion , instead of sanding down the end of your tube to match your muzzle brake, I would have reduce the length of the muzzle break so the diameter matches up perfectly with the diameter of the carbon tube then it would look seamless. The Tube comes in for about 10 inches long, just good for the whole barrel but too much to use the muzzle brake to offset it.. And you are right ~ sanding down so much is not a creative job at all ~ [emoji38] I got a 14 inches barrel. 10 inches tubes, barrel band and muzzle brake take 1.5inches, and steel breech takes the remained 2.5inches. I used the small cutting wheel from my Dremel tool set to cut the carbon fiber tube to the length I needed. Then use sand paper to make it level well and fit between the muzzle brake and the barrel band... Then the other piece (short one) was put between the steel breech and the barrel band... I got two tubes, one black and one blue... My daughter helped me made up the decision to use the black color. The blue ring at the end is because I sanded too much (!!~_~) and it's getting so loose when I put everything on! So I have to cut another little piece from the blue tube to insert it behind the muzzle brake... Sent from my S8 via Tapatalk |
|
| Author: | walther [ Sun Sep 15, 2019 5:24 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
The overall look is very nice. I've got tubing that fits the CR 600 W barrels perfectly I've been waiting to do the same thing just haven't decided on a couple of minor detail so I've been putting it off. |
|
| Author: | YepYep [ Sun Sep 15, 2019 5:39 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
[emoji38] so lucky to have a blue tube, otherwise will have to cut a small piece from another black tube would be stupid ~ Looking forward to see your Carbon-600~ Sent from my S8 via Tapatalk |
|
| Author: | wesb2007 [ Sun Sep 15, 2019 6:05 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
Turned out great. You've convinced me to order some for the Artemis guns. Sent from my EML-L09 using Tapatalk |
|
| Author: | CBS shooter [ Tue Sep 24, 2019 9:55 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
Removed a .001" thick shim from bottle reg. hope it gets me under 20 fpe. was 22.3fpe. adjusted the sear engagement then the over travel and the pull weight. what a huge Difference it made. Gauntlet Baby 
|
|
| Author: | airmec [ Fri Sep 27, 2019 6:54 pm ] | ||||
| Post subject: | Re: What Did You Do To Your Airgun Today? | ||||
I finished making the parts for the rear sight and JBwelded a new ABS blade on the barrel band of my old Crosman 137 pump pistol.
|
|||||
| Author: | kelly1 [ Fri Sep 27, 2019 7:03 pm ] |
| Post subject: | Re: What Did You Do To Your Airgun Today? |
I put a regulator on the old Daystate Air Ranger and tuned it down under 40 ft lb.(it was at 52)! |
|
| Page 30 of 32 | All times are UTC - 5 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|