Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Wed Dec 11, 2019 3:46 am

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.








Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: Sun Jul 07, 2013 10:41 am 
Offline
User avatar

Joined: Wed Dec 02, 2009 4:04 pm
Posts: 1081
Bought it from Jayzdaman in .177 cal. I do alot of gopher hunting and find .177 a little iffy on something as tough as a baseball glove.
Was looking for a .22 replacement barrel. Called around Canada and SSSO was able to bring one in for 145.00. Thought I'd keep looking. Mike Mellick from Flying Dragon carries X25 Xisco Bam clones of this gun and was going to get a clone barrel from him.

Then I decided to see if my Diana 24 .22 barrel was the same breech block as the 34. Surprise, it is.

So, tap out a few rivets, change cocking links (different lengths) fire a test shot, bam, almost done.

Pulling the cocking arm off the 24, when I pulled the pin from the linkage, two e-clips and a washer came out. Did not happen on the 34. What gives?

Tried to put the e-clips back on the pin. It is narrowed at the center, thought thats where the clips go. Too loose. Maybe on the thicker portion, too tight. Came to the conclusion that with two clips and a washer, it must have been a tight fit and pressure was holding everything together. If you have ever had the linkage apart, you would soon see how tight and difficult getting this back together would be.

Went to princess auto to look for a solution......O-rings. Picked up a multi pack and found a size that was tight enough to hold on to the narrowed part of the pin. It was tight getting it into the cocking arm slot but a little silicone grease and pop.

Pressed the pin in and it worked. Pin is in with very little movement.


Top
 Profile  
 
PostPosted: Mon Jul 08, 2013 8:14 am 
Offline
User avatar

Joined: Mon Nov 30, 2009 3:01 pm
Posts: 70
Location: KW Area, Ontario, Canada
I had the same problem with the pin, a dab of blue loctite solves the problem easy to remove with a little heat from my heat gun.

_________________
-Frank

Weihrauch 97 KT .22 cal PAL rated, Hawke Airmax 4 x 12 x 40 AO
Webley Alecto .177 & .22 Cals. with 10" Barrels
Crossman 2240 with Mods
Diana 24 .177 cal, Hawke 2x7x32 AO


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO