Canadian Airgun Forum https://www.airgunforum.ca/forums/ |
|
BSA Scorpion Hammer spring adjustment https://www.airgunforum.ca/forums/topic64411.html |
Page 1 of 1 |
Author: | UncleWayne [ Sun Sep 21, 2014 7:53 pm ] |
Post subject: | BSA Scorpion Hammer spring adjustment |
How do you remove the end cap that holds the hammer spring? Also: Is there any reason to degas the Scorpion before adjusting the hammer spring tension? |
Author: | kelly1 [ Sun Sep 21, 2014 8:07 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
UncleWayne wrote: How do you remove the end cap that holds the hammer spring? Also: Is there any reason to degas the Scorpion before adjusting the hammer spring tension? Most versions are glued on on need heat to remove.kelly |
Author: | Bistro [ Fri Sep 26, 2014 10:50 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
Next question - what's the preferred method of applying the heat... To prevent damage to any internals? |
Author: | kelly1 [ Fri Sep 26, 2014 11:56 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
Bistro wrote: Next question - what's the preferred method of applying the heat... To prevent damage to any internals? electric heat gun |
Author: | Bistro [ Tue Sep 30, 2014 6:58 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
kelly1 wrote: Bistro wrote: Next question - what's the preferred method of applying the heat... To prevent damage to any internals? electric heat gun Thanks! Thinking about adding a Huma regulator to the BSA Ultra SE and one of the adjustment steps is to remove rear cover. |
Author: | kelly1 [ Tue Sep 30, 2014 8:15 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
Bistro wrote: kelly1 wrote: Bistro wrote: Next question - what's the preferred method of applying the heat... To prevent damage to any internals? electric heat gun Thanks! Thinking about adding a Huma regulator to the BSA Ultra SE and one of the adjustment steps is to remove rear cover. You will need to degas even if it is r 10 style,is this gun like a sportman or dynamax or mor the r 10 style?..kelly |
Author: | Bistro [ Wed Oct 01, 2014 8:34 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
Yes, comfortable with all the steps, except the 'heating' part... The Ultra is likely a shorter version of the Scorpion, similar action to the R10. Huma has a decent description of the install procedures here: http://huma-air.com/wp-content/uploads/ ... BSA-SE.pdf |
Author: | Bistro [ Sat Oct 04, 2014 9:36 am ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
UncleWayne wrote: How do you remove the end cap that holds the hammer spring? Also: Is there any reason to degas the Scorpion before adjusting the hammer spring tension? Just found a simple little tool to aid the removal of the end cap on the XTX air site [I was referred to this company by Huma to order one of their regulators]. http://xtxair.com/eshop.php#!/BSA-Hamme ... ry=2849007 |
Author: | topher1266 [ Sun Oct 05, 2014 7:39 pm ] |
Post subject: | Re: BSA Scorpion Hammer spring adjustment |
I did my Dynamax which is similar and didn't have to heat anything, just remove two screws, and cap came rite off. |
Page 1 of 1 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |