Canadian Airgun Forum https://www.airgunforum.ca/forums/ |
|
Umbrae Steel Force Mock Suppressor https://www.airgunforum.ca/forums/topic77700.html |
Page 1 of 1 |
Author: | lonerider [ Sat Nov 11, 2017 1:07 pm ] |
Post subject: | Umbrae Steel Force Mock Suppressor |
Hello, I am looking for a mock suppressor for the Umarex Steel Force. I believe it has to be a "QD" type as there are no threads on the barrel. I have sent inquiries to Evike.com, Airsoft Station, and PyramidAir. Nobody is sure what will work, although I have seen several models for the airsoft guns. I was told this one "might" work https://www.airsoftstation.com/b-t-rote ... -grey-8-9/ Are there any measurements, other than length that I should look for? will any QD type silencer for a flash hider work? Thanks in advance for any advice. |
Author: | PZAM [ Sat Nov 11, 2017 3:36 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
I have both a Steel Force and a KWA/KSC/ASG MP9 handy and I can tell you that the dimensions are completely different, so I can guarantee that the typical MP9 style faux silencers made for airsoft like this will not fit, aside from the fact that they have three lugs and the Steel Force has four. The one you linked to fits over standard M4 flash-hiders (like the one supplied) and is definitely too small to fit. It looks like your only option is a custom fabricated model. |
Author: | silentman [ Sat Nov 11, 2017 3:54 pm ] | |||
Post subject: | Re: Umbrae Steel Force Mock Suppressor | |||
Took me some time to find it, but finaly did... It can be fit on top of the original flash hider, the flash hider is made of one piece it can not be removed or unscrewed. you do not need to remove it from the gun. Modif. to make it fit, all to be done on the flash hidder: 1- very fine sanding on the front, paint tickness is just what you need to make it slide in... 2- filing a notch on top and front to make the guide pin inside so the mock suppressor do not rotate... 3- a bit of filing on both side so the lock mechanism can slide and engage... To be done on the mock suppressor 4- driling a new hole on the grill covering the mock suppressor on opposite side. Cause if left as it is the writing are upside down on the right of the gun... Hummm, no picture of the flash hidder, will have to fix that... Doing it like this put's the lock facing downward. By the way, it is 6mm airsoft... https://shop.ehobbyasia.com/5ku-kac-qd- ... m-ccw.html
|
Author: | lonerider [ Sat Nov 11, 2017 10:30 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Thank you! Will give it a try |
Author: | silentman [ Sun Nov 12, 2017 10:12 am ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Found this to, here in Canada... . Look's the same with no marking... http://airsoftdepot.ca/catalog/product_ ... ts_id=4400 |
Author: | lonerider [ Sun Nov 12, 2017 1:18 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Cool....been doing some research, seems prices vary between 36 and 80 us dollars... |
Author: | silentman [ Sun Nov 12, 2017 6:19 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
lonerider wrote: Cool....been doing some research, seems prices vary between 36 and 80 us dollars... Depend where you are looking... |
Author: | silentman [ Sun Nov 12, 2017 9:02 pm ] | ||
Post subject: | Re: Umbrae Steel Force Mock Suppressor | ||
A bit of filling where the pen is pointing need's to be lightly shaved, so the lock work's perfectly. Also the notice where the notch is on the flash hider... Straight on top...
|
Author: | PZAM [ Mon Nov 13, 2017 10:31 am ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Ignore my reply further up, I was talking about the Steel Storm. |
Author: | Canadianguy [ Mon Nov 13, 2017 2:52 pm ] | ||
Post subject: | Re: Umbrae Steel Force Mock Suppressor | ||
Here's my version Steel Force with a mock suppresor. It just locks on the muzzle brake. The muzzle brake sometimes becomes a little loose! No modding at all.
|
Author: | paddyfritz [ Tue Nov 14, 2017 7:10 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
The QD cans made for an M4 are a direct fit. |
Author: | DocGadget [ Sat Dec 02, 2017 5:18 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Is it the same thing for the HK MP5 K-PDW? Would be nice to have one that can fit both... |
Author: | lonerider [ Sun Dec 03, 2017 11:42 am ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
Just wanted to say thanks to all that have given advice, it is very much appreciated. I have not been able to get on due to long hours at work and at home. I did purchase the suppressor that silentman had recommended. I will start the mods to get it to fit soon. Will I need to lengthen the barrel to the tip of the suppressor in order to shoot it with the suppressor attached? Or will it shoot straight out of the suppressor? Thanks again |
Author: | silentman [ Sun Dec 03, 2017 6:14 pm ] |
Post subject: | Re: Umbrae Steel Force Mock Suppressor |
shoot straight out of the box after modifying the flash hider, no modif on the mock supressor itself... |
Page 1 of 1 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |