Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Wed Dec 01, 2021 11:34 pm

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.






Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Wed Oct 13, 2021 6:50 pm 
Offline

Joined: Tue Nov 18, 2014 12:23 pm
Posts: 290
Location: Calgary
Are there any aftermarket link pins for break barrel Crosman rifles? The pin that holds the cocking linkage to the barrel block. The factory one on mine was peened in place and is not really useable after removal. New ones are cheap and in stock at crosman.ca but one that does not require peening for installation would be nice.

_________________
Slavia 630/77, Slavia 624, 1322, 1377, 2240, 2240/2260 20", WF600, Vantage .22
Walther Falcon Hunter .22, Walther Talon Magnum .25
CR600W .22, CR600W/Stormrider PCP .22, Diana Stormrider .177
Diana Chaser .22, Diana Bandit/PP800 PCP .25


Top
 Profile  
 
PostPosted: Wed Oct 13, 2021 7:04 pm 
Offline
User avatar

Joined: Fri Jan 22, 2010 1:17 pm
Posts: 2884
Location: Kingston, ON
TBH the OEM pin is probably your best option for the linkage. You could mod a spring pin to work, but youd need to have it fit tight in the middle and loose on the outside so the joint could rotate.

_________________

Duke ))))----//----------==


Top
 Profile  
 
PostPosted: Wed Oct 13, 2021 7:09 pm 
Offline

Joined: Tue Nov 18, 2014 12:23 pm
Posts: 290
Location: Calgary
I considered drilling and taping a hole perpendicular to the pin from below and using a set screw to hold it but I don't have a drill press and I don't think I want to free hand it. I'm also not sure that adding a set screw might not weaken the barrel block. I'll likely peen in a new factory pin but thought it was worth asking.

_________________
Slavia 630/77, Slavia 624, 1322, 1377, 2240, 2240/2260 20", WF600, Vantage .22
Walther Falcon Hunter .22, Walther Talon Magnum .25
CR600W .22, CR600W/Stormrider PCP .22, Diana Stormrider .177
Diana Chaser .22, Diana Bandit/PP800 PCP .25


Top
 Profile  
 
PostPosted: Wed Oct 13, 2021 7:48 pm 
Offline
Site Moderator

Joined: Sat Sep 03, 2005 9:25 am
Posts: 3896
Location: Ontario, Canada
I wonder if you could fabricate something simple. You could start with a bolt. Thin the head down to the thickness of a washer. Cut a groove on the other end and use a c-clip or e-clip.

Maybe you could find a steel Chicago screw (binding post) that would work.

Maybe a piece of steel rod with e-clips on the ends.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO