Canadian Airgun Forum
https://www.airgunforum.ca/forums/

Rugger 10-22 jamming
https://www.airgunforum.ca/forums/topic86494.html
Page 1 of 2

Author:  lauchlin [ Tue Aug 11, 2020 11:13 am ]
Post subject:  Rugger 10-22 jamming

Stock 10 round mag works fine then bought butler creek steel lips 25 round stove pipe and jam hell ....Next read all reviews on this one HCSR 10-22 mag was supposed to be all the rage well its no better than the butler creek and of course now i can't find the stock mag .....

Attachments:
IMG_0726n.jpg
IMG_0726n.jpg [ 231.34 KiB | Viewed 1752 times ]
IMG_0725.jpg
IMG_0725.jpg [ 391.06 KiB | Viewed 1752 times ]

Author:  leadslinger [ Tue Aug 11, 2020 11:18 am ]
Post subject:  Re: Rugger 10-22 jamming

I only ever used stock 10rd mag, or the BC 25rd mags. I always had good luck with the BC 25's

You try cleaning and lubing them up?

https://www.youtube.com/watch?v=kX5B3KohDk8

Author:  sillymike [ Wed Aug 12, 2020 10:41 am ]
Post subject:  Re: Rugger 10-22 jamming

What kind of problems?
- Failure to feed
- Failure to eject

Author:  lauchlin [ Wed Aug 12, 2020 12:28 pm ]
Post subject:  Re: Rugger 10-22 jamming

i think its called a stove pipe apparently i can't use these mag cause they can fit a pistol and a pistol can't have more than 10 rounds so these are illegal or not i have not time for that crap so going to order a couple 10 rounds to be legal :roll:

Author:  leadslinger [ Wed Aug 12, 2020 1:37 pm ]
Post subject:  Re: Rugger 10-22 jamming

lauchlin wrote:
i think its called a stove pipe apparently i can't use these mag cause they can fit a pistol and a pistol can't have more than 10 rounds so these are illegal or not i have not time for that crap so going to order a couple 10 rounds to be legal :roll:


Why not pin them?

Author:  sillymike [ Wed Aug 12, 2020 3:22 pm ]
Post subject:  Re: Rugger 10-22 jamming

For my part, most 10/22 stovepipe issues have solved by
- A good scrubbing of the chamber
- A better extractor/extractor spring
- Making sure the barrel is correctly lined-uo, as far as the extractor grove is concerned.

Are you using a aftermarket barrel?

Author:  lauchlin [ Wed Aug 12, 2020 4:07 pm ]
Post subject:  Re: Rugger 10-22 jamming

leadslinger wrote:
lauchlin wrote:
i think its called a stove pipe apparently i can't use these mag cause they can fit a pistol and a pistol can't have more than 10 rounds so these are illegal or not i have not time for that crap so going to order a couple 10 rounds to be legal :roll:


Why not pin them?

I was just reading about that i am going to do that

Author:  lauchlin [ Wed Aug 12, 2020 4:08 pm ]
Post subject:  Re: Rugger 10-22 jamming

sillymike wrote:
For my part, most 10/22 stovepipe issues have solved by
- A good scrubbing of the chamber
- A better extractor/extractor spring
- Making sure the barrel is correctly lined-uo, as far as the extractor grove is concerned.

Are you using a aftermarket barrel?

Its a all stock take down 10 22 it work fine with stock clip but no so with the bigger clips

Author:  sillymike [ Wed Aug 12, 2020 4:19 pm ]
Post subject:  Re: Rugger 10-22 jamming

Well, something is slowing down the bolt and sucking energy. If the extractor is lined up OK, you might want to put some machinist blue on top of your magazines (stock and aftermarket), put them in and cycle the action. Then compare the drag marks (if any)

Image

Author:  notec [ Wed Aug 12, 2020 4:53 pm ]
Post subject:  Re: Rugger 10-22 jamming

Judging by the top picture id say you need to take some polishing compound and smooth out the forward edge of that guide.

Author:  leadslinger [ Wed Aug 12, 2020 5:51 pm ]
Post subject:  Re: Rugger 10-22 jamming

I always ran a VQ claw extractor in my 1022s.

Also what ammo did you use?

Author:  lauchlin [ Wed Aug 12, 2020 6:23 pm ]
Post subject:  Re: Rugger 10-22 jamming

went out and bought these two clips for now 10 rounds

Attachments:
Imagen.jpeg
Imagen.jpeg [ 127.75 KiB | Viewed 1670 times ]
Imagec.jpeg
Imagec.jpeg [ 122.68 KiB | Viewed 1670 times ]
Imageb.jpeg
Imageb.jpeg [ 232.11 KiB | Viewed 1670 times ]
Image.jpeg
Image.jpeg [ 122.68 KiB | Viewed 1670 times ]

Author:  sillymike [ Wed Aug 12, 2020 7:31 pm ]
Post subject:  Re: Rugger 10-22 jamming

$37/each :shock:

Author:  lauchlin [ Wed Aug 12, 2020 7:40 pm ]
Post subject:  Re: Rugger 10-22 jamming

sillymike wrote:
$37/each :shock:

Vancouver island ...lol ...

Author:  Edmonton<500 [ Wed Aug 12, 2020 9:19 pm ]
Post subject:  Re: Rugger 10-22 jamming

Try some silicon spray in those 25s

Page 1 of 2 All times are UTC - 5 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/