Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Sun Jul 21, 2019 10:07 am

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.






Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: Pellet Trap Design
PostPosted: Wed Jun 05, 2019 4:27 am 
Offline

Joined: Wed Apr 24, 2019 7:58 pm
Posts: 16
Location: Baden, ON
Attachment:
File comment: Version-B
PT-1B.JPG
PT-1B.JPG [ 118.12 KiB | Viewed 242 times ]
Attachment:
File comment: Version-A
PT-1A.JPG
PT-1A.JPG [ 81.44 KiB | Viewed 242 times ]
I am trying to design a pellet trap for home use. I live in the country so shooting and making noise is a non-issue. Ricochets into my workshop or the neighbour's solar panels is a concern. I'm shooting with a .177 about 800 fps currently but plan to add a .22 at some point in time. Originally I wanted to set up 1/10 scale silhouettes for air rifle but I got concerned about ricochets. I'm looking at making 4 traps so I can separate the silhouettes to their appropriate distances of 20/30/36/45 yards. I also have the capability of adding kill zone sized spinners beside each silhouette.

Version-A has a simple 60 degree back on it and a flat bottom. The front edges of the side plates are bent to accept a cardboard backer and a 8-1/2x11 target. I have tapped holes in the side plates to add a couple screw to support the cardboard backer. The spinners are on a 3/8-16 threaded rod that can be quickly removed if a paper target is desired. The material is 10ga (.135") plain carbon steel. This should be sufficient to withstand .177 and .22 air rifle pellets.

Version-B is similar but I have wrapped the bottom plate back on itself similar to a Champion bullet trap capable of withstanding a .22 LR. This would give me the capability of better controlling pellets bouncing out. I have used bolts down the side to control the paper target and backer. I could also add some 1/4 flat bar to create a slot for them to slide in to. The side plates have holes at the bottom so angle or something can be bolted on for support, if required, down the road.

Is there anything I am missing or am I making this more complicated than it needs to be?


Top
 Profile  
 
 Post subject: Re: Pellet Trap Design
PostPosted: Wed Jun 05, 2019 7:03 am 
Offline
User avatar

Joined: Mon Mar 27, 2017 7:06 pm
Posts: 820
Location: Meaford, Ont.
Very nice. Version A is a dandy. Puts my wooden one to shame. When you build an extra one I will drive down and pay you for it. :wink:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO