Canadian Airgun Forum
https://www.airgunforum.ca/forums/

Custom 2240s
https://www.airgunforum.ca/forums/topic69557-15.html
Page 2 of 6

Author:  tazz [ Wed Sep 16, 2015 4:39 pm ]
Post subject:  Re: Custom 2240s

:shock: Now that's a jaw dropper Ace!!!!!!!!!!!

Author:  jezX [ Wed Sep 16, 2015 6:44 pm ]
Post subject:  Re: Custom 2240s

i have a bunch , and they are always changing , but these are a few older pic's , added some nicer grips and stuff since ,
Image
Image

Author:  prhess [ Wed Sep 16, 2015 11:53 pm ]
Post subject:  Re: Custom 2240s

Great looking pistols, everybody!!!!

Here are my 22xx...

2300T (.177) - - 1701 trigger group. Shoots like a dream!

Image

Image

2250T?? (.22) - - 1701 trigger group. 10" .22 Crosman barrel. Again, nice shooter.

Both pistol adorn grips from Steve Corcoran, he is a master.


Image


Image

Author:  rrdstarr [ Thu Sep 17, 2015 1:03 pm ]
Post subject:  Re: Custom 2240s

Love those grips prhess!!!

I could contribute, but all are disassembled. I could make about ten different gun configurations of the three basic guns I have.

Author:  Canadianguy [ Thu Sep 17, 2015 2:45 pm ]
Post subject:  Re: Custom 2240s

57scott wrote:
Brilliant-nice job,guys.
My "best" 2240 is below. Not a rifle, but well-tuned and accurate...



The grips look amazing!Where did you find them?Did they come stained and finished?

Very Nice!

Author:  FRANK [ Thu Sep 17, 2015 4:25 pm ]
Post subject:  Re: Custom 2240s

Ok I will Play Too.

Image
Image
Image
Image
Image
Image

and I'm working on a new setup. a Buntline Ya Baby.

Author:  prhess [ Thu Sep 17, 2015 9:30 pm ]
Post subject:  Re: Custom 2240s

The grips are Steve Corcoran - - Woods and Water is his and his brother's company...http://www.woodsandwateroutdoors.com/

The grips on the 2250 are laminate...

Steve sends the grips finished and ready to install.

Author:  GerardSamija [ Thu Sep 17, 2015 10:00 pm ]
Post subject:  Re: Custom 2240s

FRANK; two questions -

1) Is that a table top trebuchet in the background?

2) Are those brass set screws you've used to secure the valves in those pistols? If so, I'm a bit concerned for your safety as under high pressure they could well shear. High quality screws of some sort are required so as to avoid the valve eventually fatiguing the screws and causing a failure.

Author:  RC1947 [ Fri Sep 18, 2015 9:28 am ]
Post subject:  Re: Custom 2240s

There are some stunning examples of what can be done to the 2240. I set mine up for target shooting, and so, most of the internal work was done to the trigger. It's very accurate, and always fun to shoot. RC

Image

Author:  Whitewolf [ Fri Sep 18, 2015 11:32 am ]
Post subject:  Re: Custom 2240s

I'll bite too

Image

Built back in 2000/ 01, dubbed the Whitewolf Hunter Limited Edition. 21 were produced counting Prototype. Too hot for Canadian Law, hence sold South of the border.

Crooked Barn Breech, 10" 1322bbl, Bead Blasted and Polished, Electroless Nickel plated upon steel/ brass components, valv had been copied reproducing today's Boss Valve, Zebra Wood Target grips made by RB Grips. Laser Engraved and Numbered Breeches.
Since the pistols' production, Crosman started their Custom Shop in 2002 or 03 IIRC, adopting the Zebra Target Grips, and started production of today's Steel Breeches. Just a bit of history, there.

Author:  rrdstarr [ Fri Sep 18, 2015 12:07 pm ]
Post subject:  Re: Custom 2240s

Very cool Kim!
I always wondered what the significance was of the three pistols!
Bet they were fairly expensive with all that work!

Author:  hammerliguy [ Thu Oct 15, 2015 2:43 pm ]
Post subject:  Re: Custom 2240s

here my shorty that i got off an other forum member. i added a few parts and i think i will be adding a few more . cheers
http://i219.photobucket.com/albums/cc22 ... 640989.jpg

Author:  crossliner [ Thu Oct 29, 2015 1:17 pm ]
Post subject:  Re: Custom 2240s

Image

Author:  Hacked2Pieces [ Thu Oct 29, 2015 5:47 pm ]
Post subject:  Re: Custom 2240s

Edmonton<500 wrote:
More:
Image

Image

Image

Image

Image

Image.

Two more in the works. :mrgreen:


I recognize some of them parts ;) lol building another with thanks to some awesome people here, the devil is in the details... Hows that boringly accurate beast doing for ya Murray?

Author:  Edmonton<500 [ Fri Oct 30, 2015 1:42 am ]
Post subject:  Re: Custom 2240s

Quote:
Hows that boringly accurate beast doing for ya Murray?


Image

Page 2 of 6 All times are UTC - 5 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/