Canadian Airgun Forum

The #1 Community for Airguns in Canada!
It is currently Fri Apr 19, 2024 5:07 pm

View unanswered posts | View active topics


Board index » Main Forum » Airgun Gallery

All times are UTC - 5 hours


The Canadian Airgun Forums are a place for people to discuss and learn about airguns and the airgunning sport in Canada. There are lots of discussions about airguns, airgun accessories, reviews, modification and repair information, airgun events, field target and free classifieds!

 

You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.



Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
GimpyGolden
 Post subject: Crosman R1 SE
PostPosted: Fri Oct 30, 2020 11:14 pm 
Offline

Joined: Fri May 22, 2020 8:29 am
Posts: 81
SE = Scary Edition, cause it's a "black rifle" now.
Attachment:
Blk_R1jpg.jpg
Blk_R1jpg.jpg [ 594.52 KiB | Viewed 1342 times ]

Basically I have both FDE R1 and black DPMS Crosman's so did a lil surgery when I was bored.
The DPMS has the top cover of it's stock molded to the lower receiver so it has to be cut off to allow the R1's buffer to install.
After a little sanding it blends in.
When fitting the DPMS stock to the R1's FDE receiver the top cover is held in place by the roll pin which pins the spring guide.
All in all easy little mod that gives something unique... for now at least as I do see Crosman.ca has listed a Black R1
Top
 Profile  
 
Edmonton<500
 Post subject: Re: Crosman R1 SE
PostPosted: Fri Oct 30, 2020 11:24 pm 
Offline
User avatar

Joined: Sat Mar 16, 2013 5:15 am
Posts: 4137
Location: Edmonton
Lookin' good.
Very Scary indeed.
Perhaps looking too good. :?
Top
 Profile  
 
GimpyGolden
 Post subject: Re: Crosman R1 SE
PostPosted: Sat Oct 31, 2020 6:44 am 
Offline

Joined: Fri May 22, 2020 8:29 am
Posts: 81
Thanks
I guess I should also point out the "Barrel Device" is a "Faux Suppresor/Silencer", it is an airsoft piece as is the MST Buttstock.
Get myself in real trouble with this monstrous pop can murdering tool of the devil.
Top
 Profile  
 
GimpyGolden
 Post subject: Re: Crosman R1 SE
PostPosted: Sat Oct 31, 2020 8:22 am 
Offline

Joined: Fri May 22, 2020 8:29 am
Posts: 81
And here is the R1 as it now sits.
Attachment:
20201031_091203.jpg
20201031_091203.jpg [ 383.16 KiB | Viewed 1306 times ]

The cheek rest/cover is held at rear by roll pin but front doesn't lift even now it is no longer attached to lower receiver.
I am not a fan of the FDE so this one is setup how the kids like it.
Top
 Profile  
 
Tail Air Gunner
 Post subject: Re: Crosman R1 SE
PostPosted: Sat Oct 31, 2020 9:30 am 
Offline
User avatar

Joined: Sun Jun 28, 2020 5:24 pm
Posts: 251
Location: Montreal
GimpyGolden wrote:
SE = Scary Edition, cause it's a "black rifle" now.
Attachment:
Blk_R1jpg.jpg

Basically I have both FDE R1 and black DPMS Crosman's so did a lil surgery when I was bored.
The DPMS has the top cover of it's stock molded to the lower receiver so it has to be cut off to allow the R1's buffer to install.
After a little sanding it blends in.
When fitting the DPMS stock to the R1's FDE receiver the top cover is held in place by the roll pin which pins the spring guide.
All in all easy little mod that gives something unique... for now at least as I do see Crosman.ca has listed a Black R1


NICE job Gimpy Golden

I don't have the courage to do that to my DPMS, but I do prefer the look of yours!

If you had a YouTube video "how to" I would have tackled it

Do you have a link to the place you bought that suppressor
Is this the one you got ?
https://www.torontoairsoft.com/CYMA-MK2 ... _7153.html

or this one

https://www.torontoairsoft.com/GG-SOCOM ... _5771.html

The only mod I did to mine was added a rail riser and red dot , a new forward grip and a folding bipod
I too am not a big fan of the FDE but what you did to it makes it much better

I've also had a hard time finding an quality pistol grip, where did you find that one? and was it tricky to replace?

Cheers

T.A.G.

_________________
I like AIR!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Main Forum » Airgun Gallery

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO