I'm Ralph

New to the forum? Tell us a little about yourself.
Post Reply
Message
Author
ralphschaap
Posts: 31
Joined: Thu Dec 01, 2005 11:54 am
Location: The Netherlands
Contact:
Contact ralphschaap

I'm Ralph

#1 Post by ralphschaap »

Hello everyone, I'm Ralph from the Netherlands. I'm 22 years old and shooting since I was about 14 years. I join a shooting club and I have collected this items:

Gamo G1200
Gamo Compact
Haenel 310
Crosman Black Diamond (model 782)
Shanghai Airgun model 61
Shanghai Airgun model 62
an unkown chinese airgun....(Arrow?)
Sheridan EB20
and.. The Gat!! :shock:

I was looking for some information about an airgun when I found your website. I'm a big fan of all kinds of airguns, especially old ones.. Therefor i need a lot of information from all over the world, thats why I joined your forum :D

I hope you can understand me, my English is not very good.. But I think you can understand my English beter than when I speak Dutch haha..

Ralph
Top
User avatar
under500fps
Site sponsor and moderator
Posts: 6371
Joined: Thu Sep 22, 2005 3:40 pm
Location: Eastern Passage N.S.

#2 Post by under500fps »

Welcome to this forum
Your english is just as good as mine
I speak french & english
I have a GamoCompact & two of those .20 Benjamin-Sheridan pistols.
I trim down the pistol grip on my Gamo Compact to fit my hand better.
Image
Image

There is old airguns on that site if you are interested:
http://www.airgunners.co.nz/guns/
René
Top
ralphschaap
Posts: 31
Joined: Thu Dec 01, 2005 11:54 am
Location: The Netherlands
Contact:
Contact ralphschaap

sheridan eb

#3 Post by ralphschaap »

hey Under500fps,

Did you ever repair you're EB20? I have tryed, but i can't get the chamber out of the gun and i have to get it out, because one of the rings inside is broken or so.. It leaks co2 so i can't shoot with it.. :cry:
Top
User avatar
webstien
Site Admin
Posts: 1901
Joined: Thu Sep 01, 2005 12:08 pm
Location: Montreal, Quebec
Contact:
Contact webstien

#4 Post by webstien »

ralph, I think you have to push the valve out through the pump arm side. So you have to remove the pump arm first! and the screw holding the valve in place!
Top
User avatar
under500fps
Site sponsor and moderator
Posts: 6371
Joined: Thu Sep 22, 2005 3:40 pm
Location: Eastern Passage N.S.

#5 Post by under500fps »

Never had to repair mine yet.
So i don't know, sorry.
Image
René
Top
ralphschaap
Posts: 31
Joined: Thu Dec 01, 2005 11:54 am
Location: The Netherlands
Contact:
Contact ralphschaap

#6 Post by ralphschaap »

My Eb20 is not a pump version..
If you look at this picture:
http://www.ralphschaap.nl/luchtbuks/images/eb20.jpg

is the right grey/silver dot supposed to be a screw or something? Otherwise i can try it with a hamer or so, but i don't want to use to much force...
Top
User avatar
under500fps
Site sponsor and moderator
Posts: 6371
Joined: Thu Sep 22, 2005 3:40 pm
Location: Eastern Passage N.S.

#7 Post by under500fps »

May be you should try the (Mods & repair) section of this forum where you will find somebody with more knowledge on repairs them me.
When i had to push the valve out and in of my Challenger 2000 ,i had to use an hammer, i was scare, i would prefer going to the dentist and get a tooth pulled out :wink:
René
Top
ralphschaap
Posts: 31
Joined: Thu Dec 01, 2005 11:54 am
Location: The Netherlands
Contact:
Contact ralphschaap

#8 Post by ralphschaap »

i'm not scared to use a hamer.. :wink: But thanks for you're information, i have posted a new thread in de Mods & Repair section.
Top
Post Reply

Return to “Introduce Yourself”