Tool recommendation

Message

DoctorFrankengun · #1 Post by **DoctorFrankengun** » Mon Dec 19, 2005 5:47 pm

I found a great way to hold guns securely to work on them without the danger of scratching the finish. Two of these Wilton clamps from Canadian Tire mounted on a 2x3 in a bench vise work very well.

Jester · #2 Post by **Jester** » Mon Dec 19, 2005 7:02 pm

They look perfect for the job! How much do they cost? I've never seen them there before.

RM422 · #3 Post by **RM422** » Mon Dec 19, 2005 8:54 pm

Looks pretty handy. I too would like to know how much they cost. I need to get me a pair.

toad · #4 Post by **toad** » Mon Dec 19, 2005 11:31 pm

I guess I'm interrupting. Perhaps not allowed. A stock from a 22 Mendoza might make a good base for a kriss-bowl (get it?) Wire or cotton or wool rope? I can make the crank out of an old "come along", but what advice on the bow? Trigger etc I can figure on my own. Should I not ask on this site ( maybe lgal issues?). T

DoctorFrankengun · Mon Dec 19, 2005 11:32 pm

I got them about three weeks ago when they were on sale for $9.99. I think that the regular price was $29,99

I'm sure they will go on
sale again soon. CTC has regular sale rotations of stuff like this.

RM422 · #6 Post by **RM422** » Tue Dec 20, 2005 8:01 pm

29.99 isn't too bad but I guess I will wait till they go on sale. thanks.

Parker_101_ · #7 Post by **Parker_101_** » Sat Feb 10, 2007 1:38 pm

Well, I went to CT today and got a couple those vises, there on sale again.....
There not bad at all, from $30 each to $10 each is a big difference....
Me thinks at ten bucks a piece, for the hobbyist there's a bargain to be had...

.
Thanks for the tip DoctorFrankengun!....

#8 Post by **sniper** » Sat Feb 10, 2007 11:15 pm

Wow ... Parker, the table is looking good with that 1/4" steel plate ... congrats.

I need some those vise, I've been eyeing them since last year ... now
this is a good time to get them ..... Thx.

Parker_101_ · #9 Post by **Parker_101_** » Sat Feb 10, 2007 11:22 pm

sniper wrote:Wow ... Parker, the table is looking good with that 1/4" steel plate ... congrats.

I need some those vise, I've been eyeing them since last year ... now
this is a good time to get them ..... Thx.

Thanks
I'm looking to lay out the foundation for some accurate cuts there....

airgunner · #10 Post by **airgunner** » Wed Feb 14, 2007 10:24 am

They're on sale this week @ CTC . I just bought 2 of them for $9.99ea.
Huge saving - reg.$29.99ea!

Mort · #11 Post by **Mort** » Wed Feb 14, 2007 3:39 pm

Got a couple yesterday myself. Thanks for the heads up DoctorFrankengun.

cfraser · #12 Post by **cfraser** » Wed Feb 14, 2007 4:02 pm

LOL! Everytime those clamps go on sale (which is ~monthly it seems) I go in and eye them. I never could figure out what I needed them for, just knew I needed them...now I know! Thanks.

DoctorFrankengun · Wed Feb 14, 2007 6:02 pm

scruffie · #14 Post by **scruffie** » Wed Feb 14, 2007 7:55 pm

The CT's out here don't carry them.

CavemanDave · #15 Post by **CavemanDave** » Sun Feb 18, 2007 10:49 am

Yeah they do Scruffie. I was there yesterday and saw them but out here they aren't on sale.

Canadian Airgun Forum

Tool recommendation

Tool recommendation

wilton clamps on sale