SS Bolt for 22XX

Message

#1 Post by **sniper** » Wed Feb 22, 2006 3:54 pm

I wanted to make a bit perfect of bolt & handle. I tried the brass ... hmm... it's ok I guess but what about Stainless Steel ... now that's different. The main objective is to fit good and better functionality than the oem part beside the bling bling .... no need to shine SS, it's always shiny looking.

I found the bolt handle is problem in most cases that they don't fit correctly when pressure apply in the receiver it would kick back therefore lost in pressure perhaps is very small but "other makes" are even worst than the oem if use with CR Steel breech. This needs precision works. Also the oem o-ring is kind of loose and that is a concern ......

I tested with a 2240 out of the box and the result is amazing .... maximum increase in velocity is 8.1 fps.

#2 Post by **sniper** » Wed Feb 22, 2006 3:55 pm

#3 Post by **sniper** » Wed Feb 22, 2006 3:55 pm

#4 Post by **sniper** » Wed Feb 22, 2006 3:56 pm

#5 Post by **sniper** » Wed Feb 22, 2006 3:56 pm

#6 Post by **sniper** » Wed Feb 22, 2006 3:57 pm

#7 Post by **sniper** » Wed Feb 22, 2006 4:01 pm

Just if you're wondering where you can get them ....

http://www.airgunforum.ca/forum/viewtop ... 0823#20823

IT'S 100% MADE IN CANADA ...... YAHOOOO.....

ETA · #8 Post by **ETA** » Wed Feb 22, 2006 4:02 pm

Slick 22XX bolt and handle you got there Sniper!

Got yourself a lathe? That is some fine craftsmanship.

#9 Post by **sniper** » Wed Feb 22, 2006 4:11 pm

ETA wrote:Slick 22XX bolt and handle you got there Sniper!
Got yourself a lathe? That is some fine craftsmanship.

Thanks,

one ... I wish I got a lathe, two it would be lot of work for SS, it's very
hard steel ..... I went one step beyond ....lol.... sketch->CAD->C&C
....cut the cost down ....

Parker_101_ · #10 Post by **Parker_101_** » Wed Feb 22, 2006 4:16 pm

Congrats on the nice work sniper.....your R&D on this one looks like a winning combination....snug fitting bolt handle has to account for some increased fps....
I'm happy to hear that it's another great product made in Canada.....

#11 Post by **sniper** » Wed Feb 22, 2006 4:24 pm

Parker_101_ wrote:Congrats on the nice work sniper.....your R&D on this one looks like a winning combination....snug fitting bolt handle has to account for some increased fps....
I'm happy to hear that it's another great product made in Canada.....

Thanks Parker,

This project took about 2.5 weeks.

Helder22 · #12 Post by **Helder22** » Wed Feb 22, 2006 7:11 pm

What metal breech is that pictured on the second post?

ABshooter · #13 Post by **ABshooter** » Wed Feb 22, 2006 8:14 pm

Good job!! That bolt looks awesome.

Gotrice23 · #14 Post by **Gotrice23** » Wed Feb 22, 2006 8:23 pm

ABshooter wrote:Good job!! That bolt looks awesome.

Agreed

#15 Post by **sniper** » Wed Feb 22, 2006 8:26 pm

Thank you all.

Helder22 wrote:What metal breech is that pictured on the second post?

That's the Crosman steel breech.

Canadian Airgun Forum

SS Bolt for 22XX

SS Bolt for 22XX

What metal breech is that pictured on the second post?

Re: What metal breech is that pictured on the second post?